9.6 OSPF的DR与BDR

9.6.1 原理概述

在OSPF的广播类型网络和NBMA类型网络中，如果网络中有n台路由器，若任意两台路由器之间都要建立邻接关系，则需要建立n×(n-1)/2个邻接关系，即当路由器很多时，则需要建立和维护的邻接关系就很多，两两之间需要发送的报文也就很多，这会造成很多内容重复的报文在网络中传递，浪费了设备的带宽资源。因此在广播和NBMA类型网络中，OSPF协议定义了指定路由器DR(Designated Router),即所有其他路由器都只将各自的链路状态信息发送给DR,再由DR以组播方式发送至所有路由器，大大减少了OSPF数据包的发送。

但是如果DR由于某种故障而失效，此时网络中必须重新选举DR,并同步链路状态信息，这需要较长的时间。为了能够缩短这个过程，OSPF协议又定义了BDR(BackupDesignated Router)的概念，作为DR路由器的备份，当DR路由器失效时，BDR成为DR,并再选择新的BDR路由器。其他非DR/BDR路由器都称为DR Other路由器。

每一个含有至少两个路由器的广播类型网络或NBMA类型网络都会选举一个DR和BDR。选举规则是首先比较DR优先级，优先级高者成为DR,次高的成为BDR。如果优先级相等，则Router-ID数值高的成为DR,次高的成为BDR。如果一台路由器的DR优先级为0,则不参与选举。需要注意的是，DR是在某个广播或者NBMA网段内进行选举的，是针对路由器的接口而言的。某台路由器在一个接口上可能是DR,在另一个接口上有可能是BDR,或者是DR Other。

若DR、BDR已经选举完毕，人为修改任何一台路由器的DR优先级值为最大，也不会抢占成为新的DR或BDR,即OSPF的DR/BDR选举是非抢占的。

9.6.2 实验内容

某公司有4个部门，路由器R1连接到总经理办公室，路由器R2连接到人事部，R3连接到开发部，R4连接到市场部。4台路由器通过交换机S1互联，每台路由器都运行了OSPF路由协议，都运行在区域0内，使得公司内部各部门网络能够互相通信。由于路由器通过广播网络互连，OSPF会选举DR和BDR,现网络管理员要配置使得性能较好的R1成为DR,性能次之的R2成为BDR,而性能最差的R4不能参加DR和BDR的选举，由此来完成网络的优化。

9.6.3 实验拓扑

9.6.4 实验编址

9.6.5 实验步骤

1、基本配置

根据实验编址表进行相应的基本IP地址配置和OSPF配置，并重启OSPF进程。

[AR1]interface GigabitEthernet 0/0/0 [AR1-GigabitEthernet0/0/0]ip address 172.16.1.1 29 [AR1-GigabitEthernet0/0/0]interface GigabitEthernet 0/0/1 [AR1-GigabitEthernet0/0/1]ip address 192.168.10.254 24 [AR1-GigabitEthernet0/0/1]interface loopback 0 [AR1-LoopBack0]ip address 1.1.1.1 32 [AR1-LoopBack0]router id 1.1.1.1		# 设置环回地址作为Router-ID Info: Router ID has been modified, please reset the relative protocols manually to update the Router ID. [AR1]ospf 1 [AR1-ospf-1]area 0 [AR1-ospf-1-area-0.0.0.0]network 172.16.1.0 0.0.0.7 [AR1-ospf-1-area-0.0.0.0]network 192.168.10.0 0.0.0.255 [AR1-ospf-1-area-0.0.0.0]return reset ospf process 	# 重启OSPF进程 Warning: The OSPF process will be reset. Continue? [Y/N]:y  [AR2]interface GigabitEthernet 0/0/0 [AR2-GigabitEthernet0/0/0]ip address 172.16.1.2 29 [AR2-GigabitEthernet0/0/0]interface GigabitEthernet 0/0/1 [AR2-GigabitEthernet0/0/1]ip address 192.168.20.254 24 [AR2-GigabitEthernet0/0/1]interface loopback 0 [AR2-LoopBack0]ip address 2.2.2.2 32 [AR2-LoopBack0]router id 2.2.2.2 Info: Router ID has been modified, please reset the relative protocols manually to update the Router ID. [AR2]ospf 1 [AR2-ospf-1]area 0 [AR2-ospf-1-area-0.0.0.0]network 172.16.1.0 0.0.0.7 [AR2-ospf-1-area-0.0.0.0]network 192.168.20.0 0.0.0.255 [AR2-ospf-1-area-0.0.0.0]return reset ospf process Warning: The OSPF process will be reset. Continue? [Y/N]:y  [AR3]interface GigabitEthernet 0/0/0 [AR3-GigabitEthernet0/0/0]ip address 172.16.1.3 29 [AR3-GigabitEthernet0/0/0]interface GigabitEthernet 0/0/1 [AR3-GigabitEthernet0/0/1]ip address 192.168.30.254 24 [AR3-GigabitEthernet0/0/1]interface loopback 0 [AR3-LoopBack0]ip address 3.3.3.3 32 [AR3-LoopBack0]router id 3.3.3.3 Info: Router ID has been modified, please reset the relative protocols manually to update the Router ID. [AR3]ospf 1 [AR3-ospf-1]area 0 [AR3-ospf-1-area-0.0.0.0]network 172.16.1.0 0.0.0.7 [AR3-ospf-1-area-0.0.0.0]network 192.168.30.0 0.0.0.255 [AR3-ospf-1-area-0.0.0.0]return reset ospf process Warning: The OSPF process will be reset. Continue? [Y/N]:y  [AR4]interface GigabitEthernet 0/0/0 [AR4-GigabitEthernet0/0/0]ip address 172.16.1.4 29 [AR4-GigabitEthernet0/0/0]interface GigabitEthernet 0/0/1 [AR4-GigabitEthernet0/0/1]ip address 192.168.40.254 24 [AR4-GigabitEthernet0/0/1]interface loopback 0 [AR4-LoopBack0]ip address 4.4.4.4 32 [AR4-LoopBack0]router id 4.4.4.4 Info: Router ID has been modified, please reset the relative protocols manually to update the Router ID. [AR4]ospf 1 [AR4-ospf-1]area 0 [AR4-ospf-1-area-0.0.0.0]network 172.16.1.0 0.0.0.7 [AR4-ospf-1-area-0.0.0.0]network 192.168.40.0 0.0.0.255 [AR4-ospf-1-area-0.0.0.0]return reset ospf process Warning: The OSPF process will be reset. Continue? [Y/N]:y 

配置完成后检查OSPF的邻居建立转态，使用display ospf peer brief命令进行查看 。其他设备省略。

[AR1]display ospf peer brief 	 OSPF Process 1 with Router ID 1.1.1.1 		  Peer Statistic Information  ----------------------------------------------------------------------------  Area Id          Interface                        Neighbor id      State      0.0.0.0          GigabitEthernet0/0/0             2.2.2.2          Full          0.0.0.0          GigabitEthernet0/0/0             3.3.3.3          Full          0.0.0.0          GigabitEthernet0/0/0             4.4.4.4          Full          ---------------------------------------------------------------------------- 

2、查看默认情况下的DR/BDR状态

使用display ospf peer命令查看此时默认情况下ospf网络中的DR/BDR选举情况。

[AR1]display ospf peer 	 OSPF Process 1 with Router ID 1.1.1.1 		 Neighbors   Area 0.0.0.0 interface 172.16.1.1(GigabitEthernet0/0/0)'s neighbors  Router ID: 2.2.2.2          Address: 172.16.1.2          State: Full  Mode:Nbr is  Master  Priority: 1    DR: 172.16.1.1  BDR: 172.16.1.2  MTU: 0        Dead timer due in 34  sec     Retrans timer interval: 5     Neighbor is up for 00:34:29         Authentication Sequence: [ 0 ]    Router ID: 3.3.3.3          Address: 172.16.1.3          State: Full  Mode:Nbr is  Master  Priority: 1    DR: 172.16.1.1  BDR: 172.16.1.2  MTU: 0        Dead timer due in 34  sec     Retrans timer interval: 5     Neighbor is up for 00:26:06         Authentication Sequence: [ 0 ]    Router ID: 4.4.4.4          Address: 172.16.1.4          State: Full  Mode:Nbr is  Master  Priority: 1    DR: 172.16.1.1  BDR: 172.16.1.2  MTU: 0        Dead timer due in 32  sec     Retrans timer interval: 5     Neighbor is up for 00:15:30         Authentication Sequence: [ 0 ]  

可以观察到此时的网络中，R1是DR，R2是BDR。

接下来在每台设备上的相关接口下使用ospf ntwork-type p2mp命令修改OSPF的网络类型为点对多点。

[AR1]interface GigabitEthernet 0/0/0 [AR1-GigabitEthernet0/0/0]ospf network-type p2mp  [AR2]interface GigabitEthernet 0/0/0 [AR2-GigabitEthernet0/0/0]ospf network-type p2mp  [AR3]interface GigabitEthernet 0/0/0 [AR3-GigabitEthernet0/0/0]ospf network-type p2mp  [AR4]interface GigabitEthernet 0/0/0 [AR4-GigabitEthernet0/0/0]ospf network-type p2mp 

再次查看R1上面的OSPF的DR/BDR选举情况。

[AR1]display ospf peer 	 OSPF Process 1 with Router ID 1.1.1.1 		 Neighbors   Area 0.0.0.0 interface 172.16.1.1(GigabitEthernet0/0/0)'s neighbors  Router ID: 2.2.2.2          Address: 172.16.1.2          State: Full  Mode:Nbr is  Master  Priority: 1    DR: None   BDR: None   MTU: 0        Dead timer due in 109 sec     Retrans timer interval: 0     Neighbor is up for 00:02:01         Authentication Sequence: [ 0 ]    Router ID: 3.3.3.3          Address: 172.16.1.3          State: Full  Mode:Nbr is  Master  Priority: 1    DR: None   BDR: None   MTU: 0        Dead timer due in 94  sec     Retrans timer interval: 0     Neighbor is up for 00:02:01         Authentication Sequence: [ 0 ]    Router ID: 4.4.4.4          Address: 172.16.1.4          State: Full  Mode:Nbr is  Master  Priority: 1    DR: None   BDR: None   MTU: 0        Dead timer due in 117 sec     Retrans timer interval: 0     Neighbor is up for 00:01:31         Authentication Sequence: [ 0 ]  

可以看到DR/BDR都为none，验证了在点对多点的网络类型中不选举DR/BDR。

3、根据现在网络需求影响DR/BDR选举

R1为DR，R2为BDR，R4不参与选举。先恢复为默认的广播网络类型。然后修改R1上GE 0/0/0接口的DR优先级为100，R2为50，R3保持不变，R4为0.配置好要记得重启OSPF进程。

[AR1]interface GigabitEthernet 0/0/0 [AR1-GigabitEthernet0/0/0]ospf network-type broadcast [AR2]interface GigabitEthernet 0/0/0 [AR2-GigabitEthernet0/0/0]ospf network-type broadcast [AR3]interface GigabitEthernet 0/0/0 [AR3-GigabitEthernet0/0/0]ospf network-type broadcast [AR4]interface GigabitEthernet 0/0/0 [AR4-GigabitEthernet0/0/0]ospf network-type broadcast # 修改路由器上GE 0/0/0接口的DR优先级，R1为100，R2为50，R3保持不变，R4为0 [AR1-GigabitEthernet0/0/0]ospf dr-priority 100 [AR2-GigabitEthernet0/0/0]ospf dr-priority 50 [AR4-GigabitEthernet0/0/0]ospf dr-priority 0